Garage Door Threshold Seal Kit (1" High) Ramp Design

Part Number: WS007
From $74.37
powered by
Garage Door Threshold Seal Kit (1" High) Ramp Design 5 30

* Required Fields

From $74.37
Unit quantity: Each


The Garadry (1" High) ramp design high garage door threshold seal kit has been designed to form a watertight seal between the garage door and the floor. The threshold will also prevent leaves, dust and debris from being blown under the garage door, thus ensuring a clean and dry environment.

The kit includes:

  • Garadry threshold
  • Black adhesive (290ml)
  • Fitting instructions

This product is protected by a Community Design Registration (002188102).
Installation Instructions

Suitable to fit with a manual or automatic up and over, side hinged, roller and sectional garage doors.


Surface must be clean and free from dust, oil or grease. Fitting Garadry floor seal on loose concrete or gravel floor is not recommended. Where the surface is painted a wire brush should be used on the area where the floor seal will be fitted.

Tools required

Tape measure
Hacksaw or sharp scissors
Sealant gun

Step 1

Fitting Step One
Open the garage door and measure the overall width of the opening. Allow approximately 40mm (1 1/2 inches) overhang to allow the floor seal to be notched back around the door frame. Then cut the seal length to size.

Step 2

Fitting Step Two
Position the seal so that when the garage door closes the hump is behind the garage door.

Step 3

Fitting Step Three
From inside the garage, with the door closed, push the seal up to the back of the door with the hump touching the door, or as tight as it will go. Mark along the back edge of the floor seal with a pencil or suitable marker.

Step 4

Fitting Step Four
Open the door and mark a line along the front edge of the seal. Remove the seal and mark two parallel lines approximately 0.4" inside the existing lines. Then mark a zigzag line in the middle of them.

Step 5

Fitting Step Five
Using black MS Polymer adhesive apply the adhesive to the floor following the pencil lines created.  Recommended application temperature +5 C to +25 C.

Step 6

Fitting Step Six
Starting from one side, place the seal on the adhesive and press firmly downwards. Continue along the rest of the seal, ensuring good contact at all points.  Remove any excess adhesive from the sides with a cloth.  Allow 24 hours before driving over the threshold seal.
Additional Information

Product information

          √  Comes as a complete kit (with everything you need to fit the threshold)
          √  Suitable for use with manual/automatic up and over, side-hinged, roller and sectional garage doors



          √  Prevents leaves, dust, debris and wind-blown rainwater from entering the garage
          √  Prevents small rodents from entering the garage
          √  Reduces the damaging effects of condensation (rusting)
          √  Alternative to fitting an aqua grid
          √  Has been rigorously tested to ensure the threshold stays in place when driven over
          √  Designed by a fully qualified Industrial Designer
          √  Available in a range of lengths and heights (see drop down menu)
          √  Is fitted to the floor by sealant
          √  Made from a durable thermoplastic material
          √  100% recyclable (so you’re ‘doing your bit’ for the environment!)



What are the dimensions of the threshold?

There are eight available lengths (7’3”, 8’3”, 10’3”, 12’3”, 14’3”, 16’3”, 18’3”and 20’3”)


Does the raised hump of the threshold fit in front or behind the garage door?

The raised hump on the top of the threshold fits behind the garage door to ensure that a tight seal is formed when the garage door is in the closed position.


Is the threshold able to withstand the weight of a vehicle being driven over it?

Yes, the threshold is secured to the floor by a very strong sealant.  The threshold has also been tested rigorously to ensure that it stays in place when being driven over.


How does the garage door threshold perform in different weather conditions?

Our threshold seals can handle extreme temperatures without any issue. Our specialist sealant/adhesive does become slightly harder to apply in lower temperatures but once installed it will work just fine. If you can, install the threshold above freezing to ensure you get the best seal.

Is the threshold easy to fit?

Yes.  The threshold should take no longer than 20 minutes to fit. It requires only one adult for fitting and comes with easy-to-follow written fitting instructions.  A video showing step-by-step fitting instructions is also available online.  Click the fitting instructions tab to watch the video now.


How should I fit the threshold if my garage floor is uneven?

If you have a very uneven garage floor you may either apply extra sealant to any hollow areas so that the threshold is fitted on an even surface or you may purchase our 0.98" high ramp design threshold which has been designed specifically for uneven garage floors.  *Please note however that this threshold will only work for gaps of 0.98" or less.  Alternatively, please contact us for more information/guidance about fitting a threshold on an uneven surface and one of our team will be happy to help you. 


How long after fitting may I step on/drive over the threshold?

It is recommended that you allow a minimum of 24 hours before stepping on/driving over the threshold to ensure maximum bonding to the floor.


How durable is the threshold?

We have designed the threshold to be extremely durable.  It is made from a thermoplastic material which is both robust and durable.  We also provide a five-year guarantee with the threshold for your peace of mind (T&C's apply).


How safe is the threshold?

The threshold has been designed with safety in mind. The bright yellow warning line provides a visual reminder to those stepping into/out of the garage and is designed to prevent trips and falls.


Additional Information

Part Number WS007
Product Weight kg
Unit quantity Each
Manufacture Guarantee 1 year
Delivery & Returns


Click here for delivery prices and timeframes.

Click here for returns information.

Product Reviews

eKomi Product Feedback

See the last seven reviews of our customers.

12.07.2017 | 23:08

I highly recommend the product, the\nease of installation, and it's "end result" effectiveness for solving the problem.
30.06.2017 | 18:14

Did what it supposed to do and it adds a nice look
22.06.2017 | 14:18

Easy to install - works well
03.11.2016 | 13:44

I had water intrusion into my shop coming from poor grading and a leaky seal at the garage door. This product solved my problem completely. I would highly recommend this solution to anyone with similar issues. I am very happy with the service Garadry provides and this product.
25.10.2016 | 15:11

A great product to act as a secondary barrier to keep storm water out of my garage. Heavy duty materials. Good instructions and a fast installation.
05.10.2016 | 14:50

This is an excellent product. It was easy to install and has kept the water from leaking under my garage door. I recommend your product to everyone I tell about it.\nSteve, USA
13.07.2016 | 10:52

The garage door threshold seal is sturdy, fit for purpose and I am glad to recommend it to others.