1" High Commercial Door Aluminum Threshold Seal Kit

Part Number: WS012
From $122.17
powered by
1" High Commercial Door Aluminum Threshold Seal Kit 4.6 36

* Required Fields

From $122.17
Unit quantity: Each
Description

Details

Note: The aluminum is supplied in joinable sections, with continuous lengths of the thermoplastic seals. Please see additional information tab below for details

The Garadry commercial threshold kit has been designed to form a watertight seal between the commercial shutter or garage door and the floor. The threshold will also prevent leaves, dust and debris from being blown under the shutter/garage door, thus ensuring a clean and dry environment.

The kit includes:

  • aluminum section(s) complete with bottom and top seals
  • Tapcon fixings ( approximately 3 per 23")
  • 1 x socket head (for use with an electric screwdriver)
  • Fitting Instructions

This product is protected by a Community Design Registration (005798410-0001).

Product Reviews

eKomi Product Feedback

See the last seven reviews of our customers.

12.02.2019 | 03:44

I used this product to cover and protect the seam from my asphalt driveway and my concrete garage floor. It worked perfectly and the way you splice the two lengths together was awesome. I also admired the rubber tabs that easily are placed in the feet of the product to provide extra cushion.
30.04.2018 | 16:19

great product, thank you.
05.04.2018 | 02:54

Good product
07.03.2018 | 17:54

Goo seal kit
13.07.2016 | 10:52

Stopped the problem of water coming into my garage under the gap of the garage door. Very good solution by Garadry. Thank you.
Installation Instructions

Fitting instructions - Garadry Commercial Threshold Seal Kit 1" (High)

Suitable to fit with a manual or automatic commercial roller, sectional doors and up & over, roller and sectional domestic garage doors.

Preparation

For best results the surface should be smooth and flat and devoid of bumps or troughs.  Remedial action should be undertaken to rectify uneven surfaces prior to fitting the Threshold Seal. 

Tools Required

Tape measure
Hacksaw  
Pencil or marker pen
Stanley Knife
Drill
6mm masonry drill bit 
Electric screw driver

Kit includes:             

aluminum Section(s) to fit the aperture
Two bottom rubber seals
One black & yellow inset
Tapcom Dome Head Fixings (2.3") approx 3 per 23"
Drive Style T30 hex socket head for an electric screwdriver
Fitting Instructions (for appropriate aperture size)

 

 

Step 1

Fitting Step One
(Position A)  The Threshold Seal may be fitted to the floor directly beneath the door so that the door closes on the top of the Threshold Seal.

Or            

(Position B) The Threshold Seal may be fitted to the floor immediately behind the door if a side ground alarm system is in place.              Please note - Up and over domestic garage doors should fit the Threshold Seal behind the door (Position B) 

Step 2

Fitting Step Two
Measure the width of the opening.

Step 3

Fitting Step Three
Cut the aluminum sections(s) and the two bottom rubber seals to the size of the aperture.

Step 4

Fitting Step Four

(Position A) Position the Threshold Seal in line with the centre of the door so the door will close on the black and yellow cap that runs along the centre of the aluminum section(s). 

Then pull out the black and yellow rubber inset. 
With a pencil, make a mark where the pre-drilled holes are.
              
(Position B) Position the Threshold Seal so it is tight up against the back of the door. Then pull out the black and yellow centre cap.  

With a pencil make a mark where the holes are.  

Please note If the door has an alarm fitted to the door please check the alarm connections are in place before fixing the threshold to the floor.

Step 5

Fitting Step Five
Remove the Threshold Seal and using a 0.23" masonry drill bit, drill holes in to the floor where you have marked the ground. (Drill holes are spaced approximately every 7.8" and 1.9" from each end). 

Step 6

Fitting Step Six
Re-position the Threshold Seal so that the pre-drilled holes in the aluminum seal coincide with the holes drilled in the concrete floor.  Starting from one end, place each fixing screw into a hole. There is no need to use plugs as the fixings have a cut thread design that enables them to be drilled into concrete.

Step 7

Fitting Step Seven
Using an electric screwdriver with the screwdriver bit T30, tighten the fixing until the screw is approximately 0.2" from going all the way in.

Step 8

Fitting Step Eight
Apply pressure on the Threshold Seal by standing on it. This will compress the two side seals. Then tighten the fixing fully. 

Please note do not over tighten the screws.

Continue this process until the threshold is secured to the ground.

Step 9

Fitting Step Nine
Clean out the channel with a clean cloth to remove excess dirt.  Starting from one end of the threshold, pinch the legs of the rubber black and yellow inset and push it in to the top of the threshold  until it ‘snaps into place’.  Continue this process with the remainder of the threshold, taking care to ensure that it is firmly pushed down.

Product Reviews

eKomi Product Feedback

See the last seven reviews of our customers.

12.02.2019 | 03:44

I used this product to cover and protect the seam from my asphalt driveway and my concrete garage floor. It worked perfectly and the way you splice the two lengths together was awesome. I also admired the rubber tabs that easily are placed in the feet of the product to provide extra cushion.
30.04.2018 | 16:19

great product, thank you.
05.04.2018 | 02:54

Good product
07.03.2018 | 17:54

Goo seal kit
13.07.2016 | 10:52

Stopped the problem of water coming into my garage under the gap of the garage door. Very good solution by Garadry. Thank you.
Additional Information

Product information

  Comes as a complete kit (with everything you need to fit the aluminum threshold)
√  Suitable for use with manual/automatic up and over, side-hinged, roller and sectional garage doors as well as roller shutter doors.

Kit Sizes

Kit sizeAluminum Sections
6'6" (2m) 1x 6'6" (2m)
8'2" (2.5m) 1x 8'2" (2.5m)
3.1m 2x 5'1" (1.55m)
4m 2x 6'6" (2m)
5m 2x 8'2" (2.5m)
5.6m 2x 5'1" (1.55m) & 1x 8'2" (2.5m)
6m 3x 6'6" (2m)
7m 2x 8'2" (2.5m) & 1x 6'6" (2m)
8m 4x 6'6" (2m)
9m 2x 8'2" (2.5m) & 2x 6'6" (2m)

Threshold Weight Guide

Threshold weight guide

Please note this is a guide only. Actual vehicle weights may vary. [Click to enlarge]

Features

  Ideal for use with roller shutter/commercial doors 
  Prevents draughts
√  Prevents leaves, dust, debris and wind-blown rainwater from entering the garage 
√  Reduces the damaging effects of condensation (rusting)
  Made from extremely robust and durable materials 
  Is designed to withstand extreme weigh (e.g. forklift and vehicles including lorries)
  Comes with continuous lengths of bottom seals so that any combination of aluminum sections may be used and a watertight seal is always achieved. 
√  Removable top cap to hide / protect screws
  Is fitted to the garage floor by screws
  Designed by a fully qualified Industrial Designer
  Available in various lengths by butting sections of aluminum together
  Vertical legs underneath the threshold compress to form a watertight seal

FAQ

WHAT ARE THE DIMENSIONS OF THE 0.98" (HIGH)aluminum THRESHOLD? 

There are eight available combination lengths (6'6", 8'2", 10'2", 13'1", 14'8", 16'4", 18'4", 20'4", 22'11", 26'2", 29'6") *with continuous bottom seals.

 Technical drawing

IN WHICH POSITION SHOULD THE THRESHOLD BE FITTED?

The aluminum threshold may be fitted in one of two ways; 

Position A - Directly beneath the door so that the door closes on the top of the threshold
Position B - Immediately behind the door (if a side ground alarm system is in place).  
 
*We recommend fitting the threshold in Position B for use with up and over domestic garage doors.

 Fitting positions

IS THE THRESHOLD ABLE TO WITHSTAND THE WEIGHT OF A VEHICLE / LORRY BEING DRIVEN OVER IT?

Yes, the threshold is made from strong aluminum and secured to the floor by screws. The threshold has also been tested rigorously to ensure that it stays in place when being driven over.

IS THE THRESHOLD EASY TO FIT?

Yes.  The threshold should take no longer than 30 minutes to fit. It requires only one adult for fitting and comes with easy-to-follow written fitting instructions.  A video showing step-by-step fitting instructions is also available online.  Click the fitting instructions tab to watch the video now. 

HOW IS A CONTINUOUS LENGTH ACHIEVED?

The sections of aluminum threshold have been designed in such a way that allows the top and bottom seals to interlock the sections and provide a watertight continuous length. See the images below for an explanation of this.

HOW SHOULD I FIT THE THRESHOLD IF MY GARAGE FLOOR IS UNEVEN?

Most garage floors are uneven but if you have a very uneven garage floor you may apply sealant to any hollow areas so that the threshold is fitted on an even surface.  Please contact us for more information/guidance about fitting a threshold on an uneven surface and we will be happy to help. 

HOW LONG AFTER FITTING MAY I STEP ON/DRIVE OVER THE THRESHOLD?

Immediately.  *Unless you have a particularly uneven floor and have had to bed the threshold on a layer of sealant.  In this instance it is recommended that you allow a minimum of 24 hours before stepping on/driving over the threshold to ensure maximum bonding to the floor.

HOW DURABLE AND SAFE IS THE THRESHOLD?

We have designed the threshold to be extremely durable.  It is both robust and durable.  We also provide a five-year guarantee with the threshold for your peace of mind (T&C's apply). 

The threshold has been designed with safety in mind. The bright yellow warning lines across the top of the threshold provides a visual reminder to those stepping into/out of the garage/premises and is designed to prevent trips and falls.

Fitting the threshold

WILL THE THRESHOLD IMPROVE THE OVERALL LOOK OF MY GARAGE/PREMISES?We think so!  See the before and after images below for yourself.

yellow line


Product Reviews

eKomi Product Feedback

See the last seven reviews of our customers.

12.02.2019 | 03:44

I used this product to cover and protect the seam from my asphalt driveway and my concrete garage floor. It worked perfectly and the way you splice the two lengths together was awesome. I also admired the rubber tabs that easily are placed in the feet of the product to provide extra cushion.
30.04.2018 | 16:19

great product, thank you.
05.04.2018 | 02:54

Good product
07.03.2018 | 17:54

Goo seal kit
13.07.2016 | 10:52

Stopped the problem of water coming into my garage under the gap of the garage door. Very good solution by Garadry. Thank you.
Specification

Additional Information

Part Number WS012
Product Weight lbs
Unit quantity Each
Manufacture Guarantee 1 year

Product Reviews

eKomi Product Feedback

See the last seven reviews of our customers.

12.02.2019 | 03:44

I used this product to cover and protect the seam from my asphalt driveway and my concrete garage floor. It worked perfectly and the way you splice the two lengths together was awesome. I also admired the rubber tabs that easily are placed in the feet of the product to provide extra cushion.
30.04.2018 | 16:19

great product, thank you.
05.04.2018 | 02:54

Good product
07.03.2018 | 17:54

Goo seal kit
13.07.2016 | 10:52

Stopped the problem of water coming into my garage under the gap of the garage door. Very good solution by Garadry. Thank you.
Delivery & Returns

Delivery Information

Express & Tracked Shipping

FedEx logo
  • Orders usually shipped within 24 hours
  • Delivered in 2-3 business days
  • Shipping information will be sent out by email or SMS (if provided)

Available delivery options will be shown when you checkout. Full delivery information can be found here.

Returns Policy

  • Items may be cancelled at any point before being shipped
  • Unwanted items may be returned within 14 days of receipt of delivery

Full details on how to return any unwanted items can be found here.


Product Reviews

eKomi Product Feedback

See the last seven reviews of our customers.

12.02.2019 | 03:44

I used this product to cover and protect the seam from my asphalt driveway and my concrete garage floor. It worked perfectly and the way you splice the two lengths together was awesome. I also admired the rubber tabs that easily are placed in the feet of the product to provide extra cushion.
30.04.2018 | 16:19

great product, thank you.
05.04.2018 | 02:54

Good product
07.03.2018 | 17:54

Goo seal kit
13.07.2016 | 10:52

Stopped the problem of water coming into my garage under the gap of the garage door. Very good solution by Garadry. Thank you.